Skip to main content

GAGA-1: Capsule paint job

So with a couple of hours to work on GAGA-1 this weekend I did one simple thing: painted the capsule fluorescent yellow. Most of the other high-altitude balloon projects that I've read about have used fairly simple capsules that are covered in duct tape, or simply left white.

I decided to make the GAGA-1 capsule really visible for two reasons:

1. I want to be able to find it. Since the balloon will most likely come down somewhere in Norfolk or Suffolk (both of which are largely rural), it's going to end up in a field somewhere. The flight and recovery computers should tell me where, but I still want to be able to see it clearly when I get close.

2. If the capsule with its parachute should come down near people or vehicles, I want them to be able to see if coming. I'll be using a brightly coloured parachute, fluorescent rope and, now, a fluorescent capsule. (I'll do another blog post of safety later).

The capsule is made of expanded polystyrene which is light and insulating, but a pain to cut and paint. It's not possible to use any solvent-based paints because they eat polystyrene in seconds. Here's a shot of a polystyrene ball sprayed briefly with paint. Note the ball next to it for comparison.


That damage was done in under five minutes.

So, to paint polystyrene you need to do two things: use a water based paint and get that paint to stick. To get it to stick the polystyrene should be prepared by sanding it. I tried two things: sanding with fine wire wool (bad idea because the wire wool sticks to the polystyrene and is impossible to remove) and sanding with 240 grit sandpaper.

The sandpaper worked great. In no time at all the surface was ready for painting. I used unthinned acrylic paint from a local art shop.


And here's the final result. These pictures don't capture the full 'my eyes, my eye!' brightness of the fluorescent paint. Here you can see the yellow but not how fluorescent it is. With this paint job it should be visible.


Of course, painting the capsule adds to the weight, but I think that's going to be offset by the holes that I need to cut in it for the camera lens and antennae.



Once the paint has had time to really dry I am going to stencil on contact information so that if the capsule is lost someone can get in contact if they find it.

Comments

Dogsbody said…
I've always wondered about painting things yellow to find them in the countryside.

Admittedly yours is fluorescent yellow but unless it rains I find the countryside very grey and dusty. Just look at some of the colours that animals use to camouflage themselves (tigers, OK, not exactly native to the UK).

I forget when you are launching but the autumn leaves are already starting to fall which will be all sorts of yellow colours.

I wonder if there is a study anywhere? My guess is blue would been a good colour.

Popular posts from this blog

Your last name contains invalid characters

My last name is "Graham-Cumming". But here's a typical form response when I enter it:


Does the web site have any idea how rude it is to claim that my last name contains invalid characters? Clearly not. What they actually meant is: our web site will not accept that hyphen in your last name. But do they say that? No, of course not. They decide to shove in my face the claim that there's something wrong with my name.

There's nothing wrong with my name, just as there's nothing wrong with someone whose first name is Jean-Marie, or someone whose last name is O'Reilly.

What is wrong is that way this is being handled. If the system can't cope with non-letters and spaces it needs to say that. How about the following error message:

Our system is unable to process last names that contain non-letters, please replace them with spaces.

Don't blame me for having a last name that your system doesn't like, whose fault is that? Saying "Your last name …

All the symmetrical watch faces (and code to generate them)

If you ever look at pictures of clocks and watches in advertising they are set to roughly 10:10 which is meant to be the most attractive (smiling!) position for the hands. They are actually set to 10:09.14 if the hands are truly symmetrical. CC BY 2.0image by Shinji
I wanted to know what all the possible symmetrical watch faces are and so I wrote some code using Processing. Here's the output (there's one watch face missing, 00:00 or 12:00, because it's very boring):



The key to writing this is to figure out the relationship between the hour and minute hands when the watch face is symmetrical. In an hour the minute hand moves through 360° and the hour hand moves through 30° (12 hours are shown on the watch face and 360/12 = 30).
The core loop inside the program is this:   for (int h = 0; h <= 12; h++) {
    float m = (360-30*float(h))*2/13;
    int s = round(60*(m-floor(m)));
    int col = h%6;
    int row = floor(h/6);
    draw_clock((r+f)*(2*col+1), (r+f)*(row*2+1), r, h, floor(m…

The Elevator Button Problem

User interface design is hard. It's hard because people perceive apparently simple things very differently. For example, take a look at this interface to an elevator:


From flickr

Now imagine the following situation. You are on the third floor of this building and you wish to go to the tenth. The elevator is on the fifth floor and there's an indicator that tells you where it is. Which button do you press?

Most people probably say: "press up" since they want to go up. Not long ago I watched someone do the opposite and questioned them about their behavior. They said: "well the elevator is on the fifth floor and I am on the third, so I want it to come down to me".

Much can be learnt about the design of user interfaces by considering this, apparently, simple interface. If you think about the elevator button problem you'll find that something so simple has hidden depths. How do people learn about elevator calling? What's the right amount of informati…