Skip to main content

My foxhole radio

As a child I'd made a crystal radio set and had been meaning to make one again when I came across stories of foxhole or PoW radios made from scavenged parts. These were made during the Second World War (and other wars) from copper wire from a broken motor or alternator and anything from which a diode could be fashioned.

So, I decided to give it a go. Here's my foxhole radio. It's made from: a toilet roll tube, some copper wire, a blue steel razor blade, the tip of a pencil, a piece of coat hanger and an earpiece. Connected to ground and a long wire antenna in the garden it works... just. (PoW's seem to have used the barbed wire of the prisons they were held in as antennas, I used a long piece of bell wire).

The components are:

1. A coil of enameled copper wire wound about 100 times around a toilet roll tube. I used 22 SWG wire.

2. A tuning arm made from a piece of coat hanger than can sweep across the coil to find radio stations. The coil's actual copper is exposed where the arm sweeps by sandpapering off the enamel coating.

3. A crystal earpiece.

4. A diode made from a blued steel razor blade, the point of a pencil and a safety pin. I bought a blued steel antique razor blade on eBay after having trouble with the modern blade that I blued myself.

Modern blade blued on the gas stove (I just held it with pliers in the flame until it turned blue which took just seconds).

And the antique blued steel blade from eBay:

The antique blade worked well (i.e. I was able to find sensitive spots on it with ease, the modern blade was a pain).

Here's the end of a pencil and safety pin combination:

The antenna connects to the bottom end of the sweep arm (to the screw in the middle of the picture) and the ground connects to the right hand side of the coil (to the screw at top right, the screw top left is not used). Using the radio involves finding a radio station by sweeping around and adjusting the pencil lead so that the signal is detected. I found it easiest to sweep around for some crackles and then fiddle with the pencil to find the right spot on the blade. Once found the pencil is left in place and not moved again.

The circuit is essentially the same as this classic design with my razor blade/pencil combination instead of the cat's whisker detector in the picture.

The radio works because the razor blade and lead combination form a point contact diode which is able to detect the AM radio signal.

There are three radio stations that I can hear using the set, the loudest one appears to be Sunrise Radio an AM station catering to London's Asian community. Here's a recording of a few seconds of reception using my radio (it's very quiet, turn your volume right up): MP3.

There are lots of improvements that could be made. Currently, there's no capacitor in the circuit and so it is relying on capacitance in the antenna to make a tuned circuit. Fashioning a capacitor from aluminum foil and newspaper would probably help.

Comments

Marc said…
We made them too. Crystals, razor-blade ones, the lot.
Unknown said…
Hi
I like your no-nonsense description how to go about building a set. Wiki and the rest are useless.
I have a question or two.
1. How thick was the copper wire you used and does it matter how many turns you use? The more the better or just one layer?
2. Will a quartz crystal about 30 mm (1 1/4 inch) do in place of a razor blade?
Cheers. Peter
Hi peter, i m an electronic technologist. The wire as to be 22 agw or greater. Too small would induce higher resistance. Number of turn is important, and related to coil diameter.

Dont bother with a cristal. Go buy a germanium diode if u dont want to struggle with the razor blade
This comment has been removed by the author.
...i dont have the exact turn number by heart, but u will find on internet. Better more than less but 200 woulb be prohibitive ;)
One neat layer is ok. Use tranformer winding wire ( it has an isolating varnish. U must avoid shorting winding,so when u sand the very top of coil(as describe by John), do it gently.
Unknown said…
Jean-Pierre, you've made my day. Thanks for bothering to reply... I am quite motivated now to try and build one myself.

Can the antenna be a colour bond fence (powder-coated moulded sheet steel), or a chicken wire fence (galvanised mesh), or thin plastic coated copper wire? I also have a 1/4 inch woven galvanised steel cable about 10 meters long that I could use.

Cheers
Peter
Unknown said…
Wonder.... what the diode measurement for that point contact diode thing would have been.

Popular posts from this blog

Your last name contains invalid characters

My last name is "Graham-Cumming". But here's a typical form response when I enter it:


Does the web site have any idea how rude it is to claim that my last name contains invalid characters? Clearly not. What they actually meant is: our web site will not accept that hyphen in your last name. But do they say that? No, of course not. They decide to shove in my face the claim that there's something wrong with my name.

There's nothing wrong with my name, just as there's nothing wrong with someone whose first name is Jean-Marie, or someone whose last name is O'Reilly.

What is wrong is that way this is being handled. If the system can't cope with non-letters and spaces it needs to say that. How about the following error message:

Our system is unable to process last names that contain non-letters, please replace them with spaces.

Don't blame me for having a last name that your system doesn't like, whose fault is that? Saying "Your last name …

All the symmetrical watch faces (and code to generate them)

If you ever look at pictures of clocks and watches in advertising they are set to roughly 10:10 which is meant to be the most attractive (smiling!) position for the hands. They are actually set to 10:09.14 if the hands are truly symmetrical. CC BY 2.0image by Shinji
I wanted to know what all the possible symmetrical watch faces are and so I wrote some code using Processing. Here's the output (there's one watch face missing, 00:00 or 12:00, because it's very boring):



The key to writing this is to figure out the relationship between the hour and minute hands when the watch face is symmetrical. In an hour the minute hand moves through 360° and the hour hand moves through 30° (12 hours are shown on the watch face and 360/12 = 30).
The core loop inside the program is this:   for (int h = 0; h <= 12; h++) {
    float m = (360-30*float(h))*2/13;
    int s = round(60*(m-floor(m)));
    int col = h%6;
    int row = floor(h/6);
    draw_clock((r+f)*(2*col+1), (r+f)*(row*2+1), r, h, floor(m…

The Elevator Button Problem

User interface design is hard. It's hard because people perceive apparently simple things very differently. For example, take a look at this interface to an elevator:


From flickr

Now imagine the following situation. You are on the third floor of this building and you wish to go to the tenth. The elevator is on the fifth floor and there's an indicator that tells you where it is. Which button do you press?

Most people probably say: "press up" since they want to go up. Not long ago I watched someone do the opposite and questioned them about their behavior. They said: "well the elevator is on the fifth floor and I am on the third, so I want it to come down to me".

Much can be learnt about the design of user interfaces by considering this, apparently, simple interface. If you think about the elevator button problem you'll find that something so simple has hidden depths. How do people learn about elevator calling? What's the right amount of informati…